Fully automatic double-end crimping machine
C551SSA
A completely new system! An evolved standard.
Three flutes are used to achieve excellent machining performance.
Achieves 5,340 bottles/h (L=300).
- By creating a control environment uniquely designed by KODERA, the time it takes to complete startup after powering on has been dramatically reduced compared to conventional systems.
- The power supply system and control board have been completely redesigned, improving stability and expandability.
- The use of three independent blades for cutting, leading edge stripping, and trailing edge stripping has enabled further quality improvement and faster processing speeds.
- As with the conventional C551S series, a center blade only processing mode can be selected, allowing processing according to the characteristics of wire materials, etc.
- In addition to the conventional air blowing mechanism, the coated dust is now constantly sucked up, making it less likely to scatter.
- A safe design that follows the mechanism of the reliable C551S series.
- Standard equipment includes a collector with wire presence sensor CN-4503B, a terminal reel stand (RSB or URSB), and a signal tower.
- Supports maintenance work and equipment upgrades using the same consumable parts as conventional models.
It has three independent blades: a leading stripping blade, a cutting blade, and a trailing stripping blade. In addition, the new “cut after peeling” mode has been installed, which has drastically reduced the trouble caused by strip dust remaining on the blades.
Separate dust boxes for the front carrier dust, strip dust, and rear carrier dust. Strip dust is prevented from scattering by air blowing and powerful suction.
The newly designed electrical system shares some of the power supply system and control board with the C551HXG, achieving higher stability and reliability.
Product Specifications
| Product | |
|---|---|
| Model | C551SSA |
| External dimensions | Width 1,090mm x Depth 780mm x Height 1,550mm |
| weight | 421kg |
| power supply | Single-phase AC 200V to 240V |
| Power consumption | 270Wh at rest, 891Wh at maximum |
| Air Source | 15.7â„“/min 0.5MPa *Please use clean, dry air. |
| Processing dimensions | |
|---|---|
| Tip setting value | 0.1 to 30 mm |
| Rear end setting value | 0.1 to 20 mm |
| Shortest processing dimension *1 | L1≧40mm (with optional equipment, L1≧33mm) |
| Maximum cutting length | 99,999mm |
| Cutting tolerance *1 | Within ±(0.2+0.002×L)mm <L=cutting length> |
| processed wire rod | |
|---|---|
| Applicable wire diameter *1 | AWG#12 to AWG#32 (depending on wire material) |
| Applicable line type *1 | AV, AVS, AVSS, CAVUS, KV, KIV, UL, IV, Teflon wire, etc. |
*1. The above values will vary depending on the type of wire or terminal and the wire supply conditions, so please perform test processing in advance.
Processing capacity (number of pieces processed per hour)
| full length | Number |
|---|---|
| 100mm | 5,340 bottles |
| 200mm | 5,340 bottles |
| 300mm | 5,340 bottles |
| 500mm | 5,060 bottles |
| 800mm | 4,670 bottles |
| 1,000mm | 4,430 bottles |
| 1,500mm | 3,990 bottles |
| 2,000mm | 3,610 bottles |
| 3,000mm | 3,080 bottles |
| 4,000mm | 2,700 bottles |
| 5,000mm | 2,400 bottles |
Processing conditions: Wire: 0.5sq (AWG#20), End: 4.5mm strip (crimped), Fine wire mode, Speed: 9, Core diameter: 0.85mm, Blade return: 0.2mm, Grip position: 30mm
*These are values measured by our company. Depending on the type of wire and terminal, or other processing conditions, the values may be lower than those stated.